Skip to content
Free Standard Shipping for orders over $20 USD (USA and Canada only)
Free Standard Shipping for orders over $30 USD (USA and Canada only)

Accuracy, Precision and Resolution

Can you tell what is the difference between Accuracy, Precision and Resolution?

Accuracy is how close a frequency or power measurement is to reality, whereas precision is how repeatable a measurement is within a certain error margin. Check here for more details.

In general terms, accuracy and precision are of the same magnitude in LATNEX SPA so we may specify one of them only.

Resolution is a function of the selected frequency span. The wider the span the lower the resolution.

What is the specific Frequency Accuracy in LATNEX SPA?

LATNEX SPA Model  Frequency accuracy  Internal reference device 
Signal Generator  RF-SG6 0.5ppm Advanced 52MHz TCXO
SPA-6G 0.5ppm in 6GHZ, 10ppm below 3GHz Advanced 52MHz TCXO and 30MHz XTAL
SPA-3G 10ppm 30MHz XTAL
SPA-50K 10ppm 30MHz XTAL

Frequency accuracy of the TCXO used is +-0.5ppm, that is +-215Hz in 433Khz band or +-1.2Khz in 2.4Ghz band.

Frequency accuracy of the crystal used is +-10ppm, that is +-4.3Khz in 433Khz band or +-24Khz in 2.4Ghz band.

The aging factor of the XTAL is +-3ppm/year. The aging factor for the TCXO is 1ppm/year.

You can get detailed specifications of the crystals used below:

Unfortunately crystal tolerance is not the only factor that has influence in the initial accuracy of the unit. PCB parasitic capacitance and manufacturing tolerance plays an important role at these high frequencies. Due to this, you may expect up to +-100ppm initial value tolerance when uncalibrated for a crystal based device.

However, ageing and stability is maintained within +-10ppm, in this case the crystal is the dominating factor (the parasitic capacitance is a manufacturing error and is not influenced by age or temperature).

TCXO based devices are immune to PCB capacitance.

What about specific value for Frequency Resolution?

Regardless of accuracy, the most limiting factor is resolution. Understanding it will help to get the best value from your instrument.

There are 112 sweep steps in LATNEX SPA Spectrum Analyzer screen. Therefore, the maximum resolution you can get is FreqSpan/112.

In other words, for a frequency span of 10Mhz, you get a resolution of 10,000Khz/112=89.3Khz . With this span in the 433Mhz band, it is clear that 89.3Khz is a larger value than 4.3Khz and therefore the accuracy doesn't play as much as an important role as resolution.

If you now reduce the span to 200Khz, then resolution gets as fine as 200Khz/112=1.8Khz . In this case, the resolution is finer than accuracy and then accuracy is the main factor to consider.

What is the accuracy and resolution of power measurements?

Resolution is 0.5dBm for all bands.

Accuracy can be understood from three different angles:

  • Absolute accuracy: this is the accuracy of dBm in absolute terms, and it has a typical value of +-5dBm when uncalibrated.
  • Relative accuracy with constant RBW: also known as linearity. For a given span and Resolution BW, the relative accuracy is typically +-3dBm or better.
  • Relative accuracy with variable RBW: If you measure the same signal with different RBW values (by changing the span), the relative accuracy may go between +-3dBm to +-10dBm typically.

Can you guarantee these values?

We can guarantee resolution but cannot guarantee accuracy.

To increase the accuracy and guarantee a specific range we would need to add a high quality calibration lab step in the production chain. If you are familiar with calibration techniques, you may know it will cost more than the LATNEX SPA itself.

Advanced users in need higher accuracy can use the frequency calibration feature available since firmware version 1.09, by following these simple instructions. A reliable RF source is the only requirement to calibrate LATNEX SPA anytime. Once calibrated it will typically exhibit a +-10ppm accuracy or better independently of PCB parasitic capacitance, actually +-5ppm is achievable.

We keep developing additional firmware features to offer additional calibration capabilities to reach sub-KHz accuracy and better amplitude accuracy in all bands.